Skip to content
OpenAdvisories

Product · Juniper Networks

Junos OS

824 known vulnerabilities.

380 results · Clear filters · Feed

  • High 8.8

    Junos OS: Reflected Cross-site Scripting vulnerability in J-Web and web based (HTTP/HTTPS) services

    Insufficient Cross-Site Scripting (XSS) protection in Juniper Networks J-Web and web based (HTTP/HTTPS) services allows an unauthenticated attacker to hijack the target user's HTTP/HTTPS session and perform administrative actions on the Junos device as the ta…

  • High 7.5

    Junos OS: jdhcpd process crash when processing a specific DHCPDv6 packet in DHCPv6 relay configuration.

    On Juniper Networks Junos OS devices configured with DHCPv6 relay enabled, receipt of a specific DHCPv6 packet might crash the jdhcpd daemon. The jdhcpd daemon automatically restarts without intervention, but continuous receipt of specific crafted DHCP messag…

  • High 7.5

    Junos OS: Receipt of malformed DHCPv6 packets causes jdhcpd to crash.

    On Juniper Networks Junos OS platforms configured as DHCPv6 local server or DHCPv6 Relay Agent, Juniper Networks Dynamic Host Configuration Protocol Daemon (JDHCPD) process might crash with a core dump if a malformed DHCPv6 packet is received, resulting with …

  • High 8.3

    Junos OS: MX Series: Services card might restart due to a race condition when DNS filtering is enabled.

    When DNS filtering is enabled on Juniper Networks Junos MX Series with one of the following cards MS-PIC, MS-MIC or MS-MPC, an incoming stream of packets processed by the Multiservices PIC Management Daemon (mspmand) process might be bypassed due to a race co…

  • High 7.8

    Junos OS: Buffer overflow vulnerability in device control daemon

    A stack buffer overflow vulnerability in the device control daemon (DCD) on Juniper Networks Junos OS allows a low privilege local user to create a Denial of Service (DoS) against the daemon or execute arbitrary code in the system with root privilege. This is…

  • High 8.3

    Junos OS: MX Series: Receipt of specific packets can cause services card to restart when DNS filtering is configured.

    When DNS filtering is enabled on Juniper Networks Junos MX Series with one of the following cards MS-PIC, MS-MIC or MS-MPC, an incoming stream of packets processed by the Multiservices PIC Management Daemon (mspmand) process, responsible for managing "URL Fil…

  • High 7.5

    Junos OS and Junos OS Evolved: RPD crash due to BGP session flapping.

    On Juniper Networks Junos OS and Junos OS Evolved devices, BGP session flapping can lead to a routing process daemon (RPD) crash and restart, limiting the attack surface to configured BGP peers. This issue only affects devices with BGP damping in combination …

  • High 7.5

    Junos OS: SRX Series: An attacker sending spoofed packets to IPSec peers may cause a Denial of Service.

    On SRX Series devices, a vulnerability in the key-management-daemon (kmd) daemon of Juniper Networks Junos OS allows an attacker to spoof packets targeted to IPSec peers before a security association (SA) is established thereby causing a failure to set up the…

  • High 8.8

    Junos OS: When a DHCPv6 Relay-Agent is configured upon receipt of a specific DHCPv6 client message, Remote Code Execution may occur.

    The DHCPv6 Relay-Agent service, part of the Juniper Enhanced jdhcpd daemon shipped with Juniper Networks Junos OS has an Improper Input Validation vulnerability which will result in a Denial of Service (DoS) condition when a DHCPv6 client sends a specific DHP…

  • High 7.5

    Junos OS: Kernel crash (vmcore) or FPC crash due to mbuf leak

    On Juniper Networks Junos OS devices, a stream of TCP packets sent to the Routing Engine (RE) may cause mbuf leak which can lead to Flexible PIC Concentrator (FPC) crash or the system to crash and restart (vmcore). This issue can be trigged by IPv4 or IPv6 an…

  • High 7.5

    Junos OS: MX Series: Denial of Service vulnerability in MS-PIC component on MS-MIC or MS-MPC

    On Juniper Networks Junos MX Series with service card configured, receipt of a stream of specific packets may crash the MS-PIC component on MS-MIC or MS-MPC. By continuously sending these specific packets, an attacker can repeatedly bring down MS-PIC on MS-MI…

  • High 7.5

    Junos OS and Junos OS Evolved: RPD crash when processing a specific BGP packet

    On Juniper Networks Junos OS and Junos OS Evolved devices, processing a specific BGP packet can lead to a routing process daemon (RPD) crash and restart. This issue can occur even before the BGP session with the peer is established. Repeated receipt of this s…

  • High 7.5

    Junos OS: MX Series: PFE crash on MPC7/8/9 upon receipt of small fragments requiring reassembly

    When a device running Juniper Networks Junos OS with MPC7, MPC8, or MPC9 line cards installed and the system is configured for inline IP reassembly, used by L2TP, MAP-E, GRE, and IPIP, the packet forwarding engine (PFE) will become disabled upon receipt of sm…

  • High 7.5

    Junos OS and Junos OS Evolved: RPD crash while processing a specific BGP update information.

    On Juniper Networks Junos OS and Junos OS Evolved devices, processing a specific UPDATE for an EBGP peer can lead to a routing process daemon (RPD) crash and restart. This issue occurs only when the device is receiving and processing the BGP UPDATE for an EBG…

  • High 8.3

    Junos OS: MX Series: Services card might restart when DNS filtering is enabled

    When DNS filtering is enabled on Juniper Networks Junos MX Series with one of the following cards MS-PIC, MS-MIC or MS-MPC, an incoming stream of packets processed by the Multiservices PIC Management Daemon (mspmand) process, responsible for managing "URL Fil…

  • High 7.5

    Junos OS and Junos OS Evolved: RPD crash due to specific BGP UPDATE packets

    On Juniper Networks Junos OS and Junos OS Evolved devices, the receipt of a specific BGP UPDATE packet causes an internal counter to be incremented incorrectly, which over time can lead to the routing protocols process (RPD) crash and restart. This issue affe…

  • High 7.5

    Junos OS: Receipt of certain genuine BGP packets from any BGP Speaker causes RPD to crash.

    An improper use of a validation framework when processing incoming genuine BGP packets within Juniper Networks RPD (routing protocols process) daemon allows an attacker to crash RPD thereby causing a Denial of Service (DoS) condition. This framework requires …

  • High 8.8
    CVE-2020-1631 Exploited

    Out of Cycle Security Advisory: Junos OS: Security vulnerability in J-Web and web based (HTTP/HTTPS) services

    A vulnerability in the HTTP/HTTPS service used by J-Web, Web Authentication, Dynamic-VPN (DVPN), Firewall Authentication Pass-Through with Web-Redirect, and Zero Touch Provisioning (ZTP) allows an unauthenticated attacker to perform local file inclusion (LFI)…

    KEV Mar 25, 2022
  • High 8.6

    Junos OS and Junos OS Evolved: Invalid BGP UPDATE sent to peer device may cause BGP session to terminate.

    In a certain condition, receipt of a specific BGP UPDATE message might cause Juniper Networks Junos OS and Junos OS Evolved devices to advertise an invalid BGP UPDATE message to other peers, causing the other peers to terminate the established BGP session, cr…

  • High 7.4

    Junos OS: MX Series: Crafted packets traversing a Broadband Network Gateway (BNG) configured with IPv6 NDP proxy could lead to Denial of Service

    Due to a new NDP proxy feature for EVPN leaf nodes introduced in Junos OS 17.4, crafted NDPv6 packets could transit a Junos device configured as a Broadband Network Gateway (BNG) and reach the EVPN leaf node, causing a stale MAC address entry. This could caus…

  • High 7.5

    Junos OS: A crafted Ethernet OAM packet received by Junos may cause the Ethernet OAM connectivity fault management process (CFM) to core.

    When an attacker sends a specific crafted Ethernet Operation, Administration, and Maintenance (Ethernet OAM) packet to a target device, it may improperly handle the incoming malformed data and fail to sanitize this incoming data resulting in an overflow condi…

  • High 7.2

    Junos OS: SRX Series: Unified Access Control (UAC) bypass vulnerability

    A vulnerability in Juniper Networks SRX Series device configured as a Junos OS Enforcer device may allow a user to access network resources that are not permitted by a UAC policy. This issue might occur when the IP address range configured in the Infranet Con…

  • High 7.5

    Junos OS & Junos OS Evolved: A specific IPv4 packet can lead to FPC restart.

    The FPC (Flexible PIC Concentrator) of Juniper Networks Junos OS and Junos OS Evolved may restart after processing a specific IPv4 packet. Only packets destined to the device itself, successfully reaching the RE through existing edge and control plane filteri…

  • High 7.5

    Junos OS: High-End SRX Series: Multicast traffic might cause all FPCs to reset.

    On High-End SRX Series devices, in specific configurations and when specific networking events or operator actions occur, an SPC receiving genuine multicast traffic may core. Subsequently, all FPCs in a chassis may reset causing a Denial of Service. This issu…

  • High 7.5

    Junos OS: vMX and MX150: Denial of Service vulnerability in packet processing

    A vulnerability in Juniper Networks Junos OS on vMX and MX150 devices may allow an attacker to cause a Denial of Service (DoS) by sending specific packets requiring special processing in microcode that the flow cache can't handle, causing the riot forwarding …

  • High 7.5

    Junos OS: PTX1000 and PTX10000 Series, QFX10000 Series using non-AFT architectures: A specific genuine packet inspected by sFlow will cause a reboot.

    This issue occurs on Juniper Networks Junos OS devices which do not support Advanced Forwarding Interface (AFI) / Advanced Forwarding Toolkit (AFT). Devices using AFI and AFT are not exploitable to this issue. An improper initialization of memory in the packe…

  • High 8.6

    Junos OS: BGP session termination upon receipt of specific BGP FlowSpec advertisement.

    A vulnerability in the BGP FlowSpec implementation may cause a Juniper Networks Junos OS device to terminate an established BGP session upon receiving a specific BGP FlowSpec advertisement. The BGP NOTIFICATION message that terminates an established BGP sessi…

  • High 8.8

    Junos OS and Junos OS Evolved: A vulnerability in JDHCPD allows an attacker to send crafted IPv6 packets and arbitrarily execute commands on the target device.

    When a device using Juniper Network's Dynamic Host Configuration Protocol Daemon (JDHCPD) process on Junos OS or Junos OS Evolved which is configured in relay mode it vulnerable to an attacker sending crafted IPv6 packets who may then arbitrarily execute comm…

  • High 7.5

    Junos OS: MX Series: In BBE configurations, receipt of a specific MPLS or IPv6 packet causes a Denial of Service

    Receipt of a specific MPLS or IPv6 packet on the core facing interface of an MX Series device configured for Broadband Edge (BBE) service may trigger a kernel crash (vmcore), causing the device to reboot. The issue is specific to the processing of packets des…

  • High 7.5

    Junos OS: Cross-Site Scripting (XSS) in J-Web

    Insufficient Cross-Site Scripting (XSS) protection in J-Web may potentially allow a remote attacker to inject web script or HTML, hijack the target user's J-Web session and perform administrative actions on the Junos device as the targeted user. This issue af…

  • High 8.8

    Junos OS and Junos OS Evolved: A vulnerability in JDHCPD allows an attacker to send crafted IPv4 packets and arbitrarily execute commands on the target device.

    When a device using Juniper Network's Dynamic Host Configuration Protocol Daemon (JDHCPD) process on Junos OS or Junos OS Evolved which is configured in relay mode it vulnerable to an attacker sending crafted IPv4 packets who may then arbitrarily execute comm…

  • High 8.6

    Junos OS: Improper handling of specific IPv6 packets sent by clients eventually kernel crash (vmcore) the device.

    Specific IPv6 packets sent by clients processed by the Routing Engine (RE) are improperly handled. These IPv6 packets are designed to be blocked by the RE from egressing the RE. Instead, the RE allows these specific IPv6 packets to egress the RE, at which poi…

  • High 7.1

    Junos OS and Junos OS Evolved: A vulnerability in JDHCPD allows an attacker to send crafted IPv4 packets may take over the code execution of the JDHCPD process.

    When a device using Juniper Network's Dynamic Host Configuration Protocol Daemon (JDHCPD) process on Junos OS or Junos OS Evolved which is configured in relay mode it vulnerable to an attacker sending crafted IPv4 packets who may remotely take over the code e…

  • High 7.8

    Junos OS: EX2300, EX3400 Series: Veriexec signature checking not enforced in specific versions of Junos OS

    Veriexec is a kernel-based file integrity subsystem in Junos OS that ensures only authorized binaries are able to be executed. Due to a flaw in specific versions of Junos OS, affecting specific EX Series platforms, the Veriexec subsystem will fail to initiali…

  • High 7.5

    Junos OS: SRX Series: Denial of Service vulnerability in srxpfe related to PIM

    A vulnerability in the srxpfe process on Protocol Independent Multicast (PIM) enabled SRX series devices may lead to crash of the srxpfe process and an FPC reboot while processing (PIM) messages. Sustained receipt of these packets may lead to an extended deni…

  • High 7.5

    Junos OS: The routing protocol process (rpd) may crash and generate core files upon receipt of specific valid BGP states from a peered host.

    A memory leak vulnerability in the of Juniper Networks Junos OS allows an attacker to cause a Denial of Service (DoS) to the device by sending specific commands from a peered BGP host and having those BGP states delivered to the vulnerable device. This issue …

  • High 7.5

    Junos OS: SRX5000 Series: flowd process crash due to receipt of specific TCP packet

    On SRX5000 Series devices, if 'set security zones security-zone <zone> tcp-rst' is configured, the flowd process may crash when a specific TCP packet is received by the device and triggers a new session. The process restarts automatically. However, receipt of…

  • High 7.5

    Junos OS: SRX Series: An attacker may cause flowd to crash by sending certain valid SIP traffic to a device with SIP ALG enabled.

    A vulnerability in the SIP ALG packet processing service of Juniper Networks Junos OS allows an attacker to cause a Denial of Service (DoS) to the device by sending specific types of valid SIP traffic to the device. In this case, the flowd process crashes and…

  • High 7.8

    Junos OS: SRX Series: A weakness in the Veriexec subsystem may allow privilege escalation.

    A vulnerability in the Veriexec subsystem of Juniper Networks Junos OS allowing an attacker to fully compromise the host system. A local authenticated user can elevate privileges to gain full control of the system even if they are specifically denied access t…

  • High 7.5

    Junos OS: SRX Series: flowd process crash due to processing of specific transit IP packets

    The flowd process, responsible for forwarding traffic in SRX Series services gateways, may crash and restart when processing specific transit IP packets through an IPSec tunnel. Continued processing of these packets may result in an extended Denial of Service…