Vendor
Juniper Networks
1,090 known vulnerabilities.
Products
531 results · Clear filters · Feed
-
Medium 5.1
Junos OS: PTX Series, QFX Series: Due to a race condition input loopback firewall filters applied to interfaces may not operate even when listed in the running configuration.
A Race Condition (Concurrent Execution using Shared Resource with Improper Synchronization) vulnerability in the firewall process (dfwd) of Juniper Networks Junos OS allows an attacker to bypass the firewall rule sets applied to the input loopback filter on a…
-
Medium 4.7
Junos OS: EX4300: Stateless firewall policer fails to discard traffic
Improper Handling of Unexpected Data in the firewall policer of Juniper Networks Junos OS on EX4300 switches allows matching traffic to exceed set policer limits, possibly leading to a limited Denial of Service (DoS) condition. When the firewall policer disca…
-
Medium 6.5
Junos OS: EX4300: FPC crash upon receipt of specific frames on an interface without L2PT or dot1x configured
A vulnerability due to the improper handling of direct memory access (DMA) buffers on EX4300 switches on Juniper Networks Junos OS allows an attacker sending specific unicast frames to trigger a Denial of Service (DoS) condition by exhausting DMA buffers, cau…
-
Medium 6.5
Junos OS Evolved: Denial of Service due to receipt of specific genuine layer 2 frames.
In Juniper Networks Junos OS Evolved, receipt of a stream of specific genuine Layer 2 frames may cause the Advanced Forwarding Toolkit (AFT) manager process (Evo-aftmand), responsible for handling Route, Class-of-Service (CoS), Firewall operations within the …
-
Medium 6.5
Junos OS: EX4300-MP/EX4600/EX4650/QFX5K Series: Packet Forwarding Engine manager (FXPC) process crashes when deployed in a Virtual Chassis (VC) configuration
On Juniper Networks EX4300-MP Series, EX4600 Series, EX4650 Series, QFX5K Series deployed as a Virtual Chassis with a specific Layer 2 circuit configuration, Packet Forwarding Engine manager (FXPC) process may crash and restart upon receipt of specific layer …
-
Medium 5.5
Junos OS: MX Series: Executing CLI command repetitively may cause the system to run out of disk space
When a MX Series is configured as a Broadband Network Gateway (BNG) based on Layer 2 Tunneling Protocol (L2TP), executing certain CLI command may cause the system to run out of disk space, excessive disk usage may cause other complications. An administrator c…
-
Medium 6.5
Junos OS: A specific BGP VPNv6 flowspec message causes routing protocol daemon (rpd) process to crash with a core.
Due to an improper check for unusual or exceptional conditions in Juniper Networks Junos OS and Junos OS Evolved the Routing Protocol Daemon (RPD) service, upon receipt of a specific matching BGP packet meeting a specific term in the flowspec configuration, c…
-
Medium 5.8
Junos OS: QFX5100-96S: DDoS protection does not work as expected.
Due to an improper Initialization vulnerability on Juniper Networks Junos OS QFX5100-96S devices with QFX 5e Series image installed, ddos-protection configuration changes will not take effect beyond the default DDoS (Distributed Denial of Service) settings wh…
-
Medium 6.5
Junos OS: SRX, vSRX Series: J-Web Path traversal vulnerability in SRX and vSRX Series leads to information disclosure.
A path traversal vulnerability in the Juniper Networks SRX and vSRX Series may allow an authenticated J-web user to read sensitive system files. This issue affects Juniper Networks Junos OS on SRX and vSRX Series: 19.3 versions prior to 19.3R2-S6, 19.3R3-S1; …
-
Medium 5.3
Junos OS: Receipt of specific packets could lead to Denial of Service in MQTT Server
An uncontrolled resource consumption vulnerability in Message Queue Telemetry Transport (MQTT) server of Juniper Networks Junos OS allows an attacker to cause MQTT server to crash and restart leading to a Denial of Service (DoS) by sending a stream of specifi…
-
Medium 6.5
Junos OS: MX Series: DDoS LACP violation upon receipt of specific layer 2 frames in EVPN-VXLAN deployment
An improper check for unusual or exceptional conditions vulnerability in Juniper Networks MX Series platforms with Trio-based MPC (Modular Port Concentrator) deployed in (Ethernet VPN) EVPN-(Virtual Extensible LAN) VXLAN configuration, may allow an attacker s…
-
Medium 5.8
Junos OS Evolved: Stateless IP firewall filter does not work as expected
An Improper Check for Unusual or Exceptional Conditions in Juniper Networks Junos OS Evolved may cause the stateless firewall filter configuration which uses the action 'policer' in certain combinations with other options to not take effect. An administrator …
-
Medium 6.5
Junos OS: ANCPD core when hitting maximum-discovery-table-entries limit
A vulnerability in the handling of internal resources necessary to bring up a large number of Layer 2 broadband remote access subscriber (BRAS) nodes in Juniper Networks Junos OS can cause the Access Node Control Protocol daemon (ANCPD) to crash and restart, …
-
Medium 6.5
Junos OS: ACX5448, ACX710: BFD sessions might flap due to high rate of transit ARP packets
A vulnerability in Juniper Networks Junos OS running on the ACX5448 and ACX710 platforms may cause BFD sessions to flap when a high rate of transit ARP packets are received. This, in turn, may impact routing protocols and network stability, leading to a Denia…
-
Medium 6.5
Junos OS: Denial of Service in ppmd upon receipt of malformed packet
A vulnerability in the distributed or centralized periodic packet management daemon (PPMD) of Juniper Networks Junos OS may cause receipt of a malformed packet to crash and restart the PPMD process, leading to network destabilization, service interruption, an…
-
Medium 6.8
Junos Space: Shared secrets stored in recoverable format and directly exposed through the UI
The Junos Space Network Management Platform has been found to store shared secrets in a recoverable format that can be exposed through the UI. An attacker who is able to execute arbitrary code in the victim browser (for example via XSS) or access cached conte…
-
Medium 6.5
Junos OS: QFX Series: Traffic loop Denial of Service (DoS) upon receipt of specific IP multicast traffic
In an EVPN/VXLAN scenario, if an IRB interface with a virtual gateway address (VGA) is configured on a PE, a traffic loop may occur upon receipt of specific IP multicast traffic. The traffic loop will cause interface traffic to increase abnormally, ultimately…
-
Medium 6.7
Junos OS: Command injection vulnerability in 'request system software' CLI command
A command injection vulnerability in install package validation subsystem of Juniper Networks Junos OS that may allow a locally authenticated attacker with privileges to execute commands with root privilege. To validate a package in Junos before installation,…
-
Medium 6.5
Junos OS: EX Series, QFX Series, SRX Branch Series, MX Series: Memory leak in packet forwarding engine due to 802.1X authenticator port interface flaps
On Juniper Networks Junos EX series, QFX Series, MX Series and SRX branch series devices, a memory leak occurs every time the 802.1X authenticator port interface flaps which can lead to other processes, such as the pfex process, responsible for packet forward…
-
Medium 5.0
Contrail Networking: Administrator credentials are exposed in a plaintext file
An Information Exposure vulnerability in Juniper Networks Contrail Networking allows a locally authenticated attacker able to read files to retrieve administrator credentials stored in plaintext thereby elevating their privileges over the system. This issue a…
-
Medium 6.5
Junos OS Evolved: Receipt of certain valid BGP update packets from BGP peers may cause RPD to core when using REGEX.
In Juniper Networks Junos OS Evolved an attacker sending certain valid BGP update packets may cause Junos OS Evolved to access an uninitialized pointer causing RPD to core leading to a Denial of Service (DoS). Continued receipt of these types of valid BGP upd…
-
Medium 6.8
Junos OS: Privilege escalation in J-Web due to arbitrary command and code execution via information disclosure from another users active session
An Information Exposure vulnerability in J-Web of Juniper Networks Junos OS allows an unauthenticated attacker to elevate their privileges over the target system through opportunistic use of an authenticated users session. This issue affects: Juniper Networks…
-
Medium 5.8
Junos OS: MX Series: Dynamic filter fails to match IPv6 prefix
When the "Intrusion Detection Service" (IDS) feature is configured on Juniper Networks MX series with a dynamic firewall filter using IPv6 source or destination prefix, it may incorrectly match the prefix as /32, causing the filter to block unexpected traffic…
-
Medium 6.5
Junos OS: SRX and NFX Series: Insufficient Web API private key protection
On Juniper Networks SRX Series and NFX Series, a local authenticated user with access to the shell may obtain the Web API service private key that is used to provide encrypted communication between the Juniper device and the authenticator services. Exploitati…
-
Medium 6.5
Junos OS: EX4300-MP/EX4600/QFX5K Series: High CPU load due to receipt of specific layer 2 frames when deployed in a Virtual Chassis configuration
On Juniper Networks EX4300-MP Series, EX4600 Series and QFX5K Series deployed in a Virtual Chassis configuration, receipt of a stream of specific layer 2 frames can cause high CPU load, which could lead to traffic interruption. This issue does not occur when …
-
Medium 6.5
Junos OS: EX4300-MP/EX4600/QFX5K Series: High CPU load due to receipt of specific layer 2 frames in EVPN-VXLAN deployment.
On Juniper Networks EX4300-MP Series, EX4600 Series and QFX5K Series deployed in (Ethernet VPN) EVPN-(Virtual Extensible LAN) VXLAN configuration, receipt of a stream of specific VXLAN encapsulated layer 2 frames can cause high CPU load, which could lead to n…
-
Medium 5.8
Junos OS: EX4600, QFX5K Series: Stateless firewall filter matching 'user-vlan-id' will cause incomplete discard action
When configuring stateless firewall filters in Juniper Networks EX4600 and QFX 5000 Series devices using Virtual Extensible LAN protocol (VXLAN), the discard action will fail to discard traffic under certain conditions. Given a firewall filter configuration s…
-
Medium 5.5
Junos OS: SRX1500, vSRX, SRX4K, NFX150, NFX250: Denial of service vulnerability executing local CLI command
An input validation vulnerability exists in Juniper Networks Junos OS, allowing an attacker to crash the srxpfe process, causing a Denial of Service (DoS) through the use of specific maintenance commands. The srxpfe process restarts automatically, but continu…
-
Medium 5.3
Junos OS: MX Series: MS-MPC/MIC might crash when processing malformed IPv6 packet in NAT64 configuration.
On Juniper Networks MX Series with MS-MIC or MS-MPC card configured with NAT64 configuration, receipt of a malformed IPv6 packet may crash the MS-PIC component on MS-MIC or MS-MPC. This issue occurs when a multiservice card is translating the malformed IPv6 p…
-
Medium 6.5
Junos OS Evolved: Receipt of a specifically malformed NDP packet could lead to Denial of Service
Receipt of a specifically malformed NDP packet sent from the local area network (LAN) to a device running Juniper Networks Junos OS Evolved can cause the ndp process to crash, resulting in a Denial of Service (DoS). The process automatically restarts without …
-
Medium 6.5
Junos OS and Junos OS Evolved: RPD can crash due to a slow memory leak.
On Juniper Networks Junos OS and Junos OS Evolved platforms with EVPN configured, receipt of specific BGP packets causes a slow memory leak. If the memory is exhausted the rpd process might crash. If the issue occurs, the memory leak could be seen by executin…
-
Medium 6.5
Junos OS: EX4300 Series: High CPU load due to receipt of specific IPv4 packets
On Juniper Networks EX4300 Series, receipt of a stream of specific IPv4 packets can cause Routing Engine (RE) high CPU load, which could lead to network protocol operation issue and traffic interruption. This specific packets can originate only from within th…
-
Medium 6.3
Junos OS: NFX350: Password hashes stored in world-readable format
The Juniper Device Manager (JDM) container, used by the disaggregated Junos OS architecture on Juniper Networks NFX350 Series devices, stores password hashes in the world-readable file /etc/passwd. This is not a security best current practice as it can allow …
-
Medium 6.5
Junos OS: EX2300 Series: High CPU load due to receipt of specific multicast packets on layer 2 interface
On Juniper Networks EX2300 Series, receipt of a stream of specific multicast packets by the layer2 interface can cause high CPU load, which could lead to traffic interruption. This issue occurs when multicast packets are received by the layer 2 interface. To …
-
Medium 6.6
Junos OS Evolved: 'console log-out-on-disconnect' fails to terminate session on console cable disconnection
The system console configuration option 'log-out-on-disconnect' In Juniper Networks Junos OS Evolved fails to log out an active CLI session when the console cable is disconnected. This could allow a malicious attacker with physical access to the console the a…
-
Medium 5.3
Junos OS: MX series/EX9200 Series: IPv6 DDoS protection does not work as expected.
On Juniper Networks MX Series and EX9200 Series, in a certain condition the IPv6 Distributed Denial of Service (DDoS) protection might not take affect when it reaches the threshold condition. The DDoS protection allows the device to continue to function while…
-
Medium 5.3
Junos OS: jdhcpd process crash when forwarding a malformed DHCP packet.
On Juniper Networks Junos OS devices configured as a DHCP forwarder, the Juniper Networks Dynamic Host Configuration Protocol Daemon (jdhcp) process might crash when receiving a malformed DHCP packet. This issue only affects devices configured as DHCP forward…
-
Medium 5.3
Junos OS: MX Series: PFE crash on MPC7/8/9 upon receipt of large packets requiring fragmentation
When a device running Juniper Networks Junos OS with MPC7, MPC8, or MPC9 line cards installed and the system is configured for inline IP reassembly, used by L2TP, MAP-E, GRE, and IPIP, the packet forwarding engine (PFE) will become disabled upon receipt of la…
-
Medium 5.6
Junos Space: OpenNMS is accessible via port 9443
OpenNMS is accessible via port 9443
-
Medium 6.5
Junos OS: MX Series: PFE on the line card may crash due to memory leak.
On Juniper Networks MX series, receipt of a stream of specific Layer 2 frames may cause a memory leak resulting in the packet forwarding engine (PFE) on the line card to crash and restart, causing traffic interruption. By continuously sending this stream of s…